How To Connect To Cognex Camera

• Contents
• Tabular array of Contents
• Bookmarks

  Besides Meet for Cognex In-Sight Micro Series

  Related Manuals for Cognex In-Sight Micro Series

  Summary of Contents for Cognex In-Sight Micro Series

• Page ane ® In-Sight Micro Serial Vision Organisation Installation Transmission 2019 August 24 Revision: 5.7.4.3...

• Page 2: Legal Notices

  Copyright © 2008 - 2019. Cognex Corporation. All Rights Reserved. Portions of the hardware and software provided past Cognex may be covered by one or more than U.South. and foreign patents, every bit well as pending U.South. and foreign patents listed on the Cognex web site at: cognex.com/patents.

• Page 3: Regulations/Conformity

  Regulations/Conformity Regulations/Conformity Note: For the nearly current CE declaration and regulatory conformity information, run across the Cognex back up site: cognex.com/support. Declaration of Conformity Cognex Corporation Manufacturer One Vision Drive Natick, MA 01760 Us In-Sight Micro 1020/1050/1100/1110/1400/1410: Type 821-0043-1R In-Sight Micro 1100C/1400C: Type 821-0044-1R...

• Folio 4: For European Community Users

  Regulations/Conformity For European Community Users Cognex complies with Directive 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste product electrical and electronic equipment (WEEE). This product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environs, if not properly disposed.

• Folio v: Precautions

  Precautions Precautions To reduce the adventure of injury or equipment harm, observe the following precautions when you lot install the Cognex product: An IEEE 802.3af compliant, and UL or NRTL listed, Ability over Ethernet (PoE) power source rated Class 0, two, 3 or 4 must be used.

• Folio 6: Table Of Contents

  Table of Contents Tabular array of Contents Legal Notices Regulations/Conformity For European Community Users Precautions Table of Contents Introduction Support Standard Components Cables Ethernet Cable Breakout Cable I/O Module Cablevision Installation Connectors and Indicators Install the Mounting Cake (Optional) Install the Lens Connect the Inputs and Outputs (Optional) Option i: Connect the Breakout Cablevision Option 2: Connect the I/O Module Cable...

• Page 7: Introduction

  Many information resources are available to help you apply the vision organisation: ® The In-Sight Explorer Help and EasyBuilder Help files, provided with In-Sight Explorer software. On-need training: cognex.com/on-need-grooming.aspx. The In-Sight online support site: cognex.com/back up/insight. Standard Components In-Sight Micro vision organization is shipped with the following standard components. Component Description...

• Page 8: Cables

  Introduction Cables Note: Cables are sold separately. Circumspection: All cable connectors are keyed to fit the connectors on the vision system. Exercise not force the connections or harm may occur. Ethernet Cable The Ethernet cable provides the Ethernet connection for network communications and supplies ability to the vision organization.

• Page 9: Breakout Cable

  Introduction Breakout Cable The Breakout cablevision provides access to the vision organisation's trigger and high-speed outputs. The Breakout cablevision can be continued to devices, such as a PLC, trigger sensor or strobe light. The pin-outs for the cablevision are listed in the Breakout Cable Specifications on page 25.

• Folio 10: Installation

  Read this section to learn how the vision organisation connects to its standard components and accessories. For a listing of options and accessories, contact your Cognex sales representative. Note: Cables are sold separately. If a standard component is missing or damaged, immediately contact your Cognex Authorized Service Provider (ASP) or Cognex Technical Back up. Connectors and Indicators Connector/Indicator...

• Folio 11: Install The Mounting Cake (Optional)

  Installation Install the Mounting Cake (Optional) The mounting kit includes a mounting bracket and M3 screws (quantity 4) for mounting the vision system and securing it to a mounting surface. The mounting bracket also has 1/4 - 20 and M6 mounting holes available for mounting the vision system to a mounting surface.

• Page 12: Connect The Inputs And Outputs (Optional)

  Installation Connect the Inputs and Outputs (Optional) The vision system's I/O connector supplies connections for the acquisition trigger and high-speed outputs. Circumspection: All cable connectors are keyed to fit the connectors on the vision system. Practice non force the connections or impairment may occur.

• Page 13: Option 2: Connect The I/O Module Cablevision

  Installation Pick 2: Connect the I/O Module Cable i. Connect the I/O Module cable'south M8 connector to the vision system I/O connector. 2. Connect the I/O Module cable's DB15 connector to the I/O module's I/O connector.

• Folio fourteen: Connect The Ethernet And Power

  Installation Connect the Ethernet and Ability The vision arrangement's PoE connector provides the Ethernet connection for network communications and supplies power to the vision system. The following steps illustrate how to connect the In-Sight Micro vision system to the In-Sight CIO-MICRO or CIO-MICRO-CC I/O module.

• Page 15: Connect The Frame Ground Wire

  Installation Connect the Frame Footing Wire Connect a frame ground wire to the I/O module's Frame Ground terminal. Connect the other finish of the frame ground wire to frame ground. Caution: The shield ground connections of the RS-232 port, LAN port, PoE port, I/O port and Frame Basis terminal are internally connected.

• Page sixteen: Connect An Rj-45 Lan Cable

  Installation Connect an RJ-45 LAN Cablevision To connect the vision system to an Ethernet network, plug a LAN cable (RJ-45 connector) into the I/O module's LAN port and connect the other end of the cable to a switch/router or PC, every bit applicable. Connect the Ethernet Cable Circumspection: All cablevision connectors are keyed to fit the connectors on the vision organisation.
• Page 17 Installation ii. Connect the Ethernet cable'due south RJ-45 connector to the I/O module's PoE port. 3. Restore power to the 24VDC power supply and turn it on if necessary.

• Folio eighteen: Specifications

  Specifications Specifications The following sections list general specifications for the In-Sight Micro vision systems. In-Sight Micro Vision System Specifications Specifications 1020/1050 1100/1110 1100C 1400/1410 1400C 1402/1412 1403/1413 1403C 1500 Minimum In-Sight version four.four.3 In-Sight In-Sight version In-Sight Firmware version iv.iv.3 version 4.ix.i Requirement 4.vi.0...
• Folio 19 Specifications Specifications 1020/1050 1100/1110 1100C 1400/1410 1400C 1402/1412 1403/1413 1403C 1500 Detached Inputs None. (Eight additional general-purpose inputs available when using the optional CIO-MICRO or CIO- MICRO-CC I/O module.) Discrete ii opto-isolated, NPN/PNP loftier-speed outputs. (Viii boosted general-purpose outputs available Outputs when using the optional CIO-MICRO or CIO-MICRO-CC I/O module.) Status LEDs Network, 2 user-configurable.

• Folio 20: I/O Specifications

  Specifications I/O Specifications Cablevision and connector specifications and connection examples for the acquisition trigger input and the loftier-speed outputs are provided in the following sections. Acquisition Trigger Input The vision organisation features i acquisition trigger input, which is optically isolated. You lot can configure the acquisition trigger input to trigger from an NPN (current sinking) or PNP (electric current sourcing) device.

• Page 21: High-Speed Outputs

  Specifications High-Speed Outputs The In-Sight Micro vision organization features two built-in, high-speed outputs, which are optically isolated. The high-speed outputs can be used as either NPN (current sinking) or PNP (current sourcing) lines. Specification Description Voltage 28VDC maximum through external load. Current 100mA maximum sink current.
• Page 22 Specifications Loftier-Speed Output - NPN Configuration The Breakout cable can exist used to connect to an NPN-compatible PLC input. Connect HS OUT 0 or HS OUT one directly to the PLC input. When enabled, the output pulls the PLC input downwards to less than 3VDC. For more information, refer to the Breakout Cable Specifications on page 25.
• Page 23 Specifications Loftier-Speed Output - Relay/LED Configuration The Breakout cablevision tin can be used to connect the high-speed outputs to a relay, LED or similar load. Connect the negative side of the load to the output and the positive side to +24VDC. When the output switches on, the negative side of the load is pulled downward to less than 3VDC, and greater than 21VDC appears across the load.

• Folio 24: Ethernet Cablevision Specifications

  Specifications Ethernet Cablevision Specifications The Ethernet cable provides the Ethernet connection for network communications and supplies power to the vision system. P1 Pivot# Indicate Proper name Wire Color P2 Pin# TPO+/+48VDC (Mode A) White/Orange TPO-/+48VDC (Mode A) Orange TPI+/+48VDC RTN (Mode A) White/Green +48VDC (Mode B) Blue...

• Page 25: Breakout Cablevision Specifications

  Specifications Breakout Cable Specifications The Breakout cable provides admission to the vision system'due south trigger and high-speed outputs. The Breakout cable can exist connected to devices, such equally a PLC, trigger sensor or strobe lite. The Breakout cable is not terminated. P1 Pivot# Bespeak Wire Color...

• Page 26: I/O Module Cable Specifications

  Specifications I/O Module Cable Specifications The I/O Module cable is used with the CIO-MICRO or CIO-MICRO-CC I/O module. The I/O Module cable connects the vision system directly to the I/O module via the DB15 connector. When connected, the I/O Module cablevision provides access to the vision system's trigger and high-speed outputs.

• Folio 27: Dimensions

  Specifications Dimensions The post-obit sections list dimensions of the vision organisation and optional accessories. Vision Organisation Dimensions Notation: Dimensions are in millimeters [inches] and are for reference purposes only. All specifications are for reference purposes only and can change without notice.

• Folio 28: Vision System Dimensions (With Mounting Cake)

  Specifications Vision Arrangement Dimensions (with Mounting Cake) Note: Dimensions are in millimeters [inches] and are for reference purposes merely. All specifications are for reference purposes only and can alter without notice.

• Folio 29: Appendix A - Cleaning And Maintenance

  Appendix A - Cleaning and Maintenance Appendix A - Cleaning and Maintenance Clean the Vision Organization Housing To clean the outside of the vision system housing, use a small amount of mild detergent cleaner or isopropyl alcohol on a cleaning fabric. Do not pour the cleaner on the vision organization housing. Caution: Practice not attempt to make clean whatever In-Sight production with harsh or corrosive solvents, including lye, methyl ethyl ketone (MEK) or gasoline.

Source: https://www.manualslib.com/manual/1806414/Cognex-In-Sight-Micro-Series.html

Posted by: munsonthadine.blogspot.com

Share this post